PurposeThe purpose of the Boss Coupling and Clamp System is to supply a convenient threaded fitting needed to connect two lengths of hose, or a single length to a male or female threaded (NPT) outlet on any type of equipment. The spud part of the coupling serves as one half of the connection and is usually fixed permanently to the equipment. The stem and nut attached (clamped) to the hose is the other half. The two halves are connected by rotating the wing nut on the spud, to achieve a mechanical as well as a pressure seal. |
ServicesThe Boss Coupling and Clamp System is designed as an all purpose system, universally recommended for steam connections. They are also widely used with equal efficiency for high or low pressure air, water, liquid petroleum gas, fluid petroleum products, chemicals, potable fluids and almost any other type of fluid or gas. (Consult Columbia Rubber & Gasket for specific media capabilities.) They can be applied to all types of rubber, synthetic, plastic, metallic (with special stems) or semi-metallic hose. |
EZ-Boss non-metallic polymer seat is not subject to corrosion and offers resistance to chemicals and steam found in manufacturing facilities. A precisely machined recess holds the seat firmly in place, allowing it to absorb harsh punishment. Recommend for steam service up to 450ºF; easy to seal; works with existing Boss Ground Joint Stems.
- | Coupling with Female Spud | Stem | Wing Nut | Female Spud | Male Spud | Double Spud |
---|---|---|---|---|---|---|
Sizes | Part # | Part # | Part # | Part # | Part # | Part # |
1/4" * | GF1 | GBA | BA2 | GBC | - | - |
3/8" * | GF3 | GCA | CB | GCC | GMC | - |
1/2" | GF6 | GB1 | B2 | GB3 | GM3 | GDB3 |
3/4" | GF26 | GB6 | B12 | GB8 | GM8 | GDB13 |
1" | GF36 | GB11 | B12 | GB13 | GM13 | GDB13 |
1-1/4" | GF51 | GB16 | B17 | GB18 | GM18 | GDB23 |
1-1/2" | GF61 | GB21 | B17 | GB23 | GM23 | GDB23 |
2" | GF81 | GB26 | B27 | GB28 | GM28 | GDB28 |
2-1/2" | GF96 | GB31 | B32 | GB33 | GM33 | GDB33 |
3" | GF111 | GB36 | B37 | GB38 | GM38 | GDB38 |
4" | GF141 | GB46 | B47 | GB48 | - | - |
6" * | GF201 | GB66 | B67 | GB68 | - | - |
- | Coupling with Female Spud | Stem | Wing Nut | Female Spud | Male Spud | Double Spud | Washer* |
---|---|---|---|---|---|---|---|
Sizes | Part # | Part # | Part # | Part # | Part # | Part # | Part # |
3/8" | WF3 | CA | CB | CC | WMC | - | WBC |
1/2" | WF6 | B1 | B2 | B3 | WM3 | DB3 | W2 |
3/4" | WF26 | B6 | B12 | B8 | WM8 | DB13 | W12 |
1" | WF36 | B11 | B12 | B13 | WM13 | DB13 | W12 |
1-1/4" | WF51 | B16 | B17 | B18 | WM18 | DB23 | W17 |
1-1/2" | WF61 | B21 | B17 | B23 | WM23 | DB23 | W17 |
2" | WF81 | B26 | B27 | B28 | WM28 | DB28 | W27 |
2-1/2" | WF96 | B31 | B32 | B33 | WM33 | DB33 | W32 |
3" | WF111 | B36 | B37 | B38 | WM38 | DB38 | W37 |
4" | WF141 | B46 | B47 | B48 | - | - | W47 |
6" | WF201 | B66 | B67 | B68 | - | - | W67 |
Steel Bar Stock | Malleable Iron | 316 Stainless Steel | Brass | ||||
---|---|---|---|---|---|---|---|
Hose x NPT Size | Part # | Size | Part # | Size | Part # | Size | Part # |
1/4" x 1/8" | MS4X2 | - | - | 1/2" | RMS1 | - | - |
1/4" x 1/4" | MSA | - | - | 3/4" | RMS6 | 3/4" | BMS6 |
1/4" x 3/8" | MSB | - | - | 1" | RMS11 | 1" | BMS11 |
3/8" x 1/4" | MS6X4 | 1-1/4" | MS16 | 1-1/4" | RMS16 | 1-1/4" | BMS16 |
3/8" x 3/8" | MSC | 1-1/2" | MS21 | 1-1/2" | RMS21 | 1-1/2" | BMS21 |
3/8" x 1/2" | MS6X8 | 2" | MS26 | 2" | RMS26 | 2" | BMS26 |
1/2" x 1/4" | MS8X4 | 2-1/2" | MS31 | 2-1/2" | RMS31 | - | - |
1/2" x 3/8" | MS8X6 | 3" | MS36 | 3" | RMS36 | 3" | BMS36 |
1/2" x 1/2" | MS1 | 4" | MS46 | - | - | - | - |
1/2" x 3/4" | MS8X12 | - | - | - | - | - | - |
3/4" x 1/2" | MS12X8 | - | - | - | - | - | - |
3/4" x 3/4" | MS6 | - | - | - | - | - | - |
3/4" x 1" | MS12X16 | - | - | - | - | - | - |
1" x 3/4" | MS16X12 | - | - | - | - | - | - |
1" x 1" | MS11 | - | - | - | - | - | - |
LP-Boss Male StemNon-porous tubular steel for volatile materials
|
Boss Hose MenderCollars to engage grip fingers of Boss Clamps
|
The bolts used in the Boss interlocking clamps are not standard bolts. They vary from standard bolts in length versus diameter, thread length and material hardness. These bolts can be retorqued, but it is not recommended that they be reused, as they are designed for a single bend only. We recommend using only factory supplied replacement bolts
Hose ID | Hose OD | Plated Malleable Iron | Stainless Steel | Brass | |||
---|---|---|---|---|---|---|---|
Size | FromE#DH> | To: | Part # | Part # | Torque** | Part # | Torque** |
1/4" | 9/16" | 21/32" | BD | - | 6 | - | - |
3/8" | 11/16" | 7/8" | CD | - | 6 | - | - |
1/2" | 13/16" | 15/16" | DD | - | 6 | - | - |
1/2" | 15/16" | 1-1/16" | B4 | RB4 | 12 | BB4 | 10 |
1/2" | 1-1/16" | 1-3/16" | B5 | - | 12 | - | - |
3/4" | 1-5/32" | 1-9/32" | BU9S | - | 21 | - | - |
3/4" | 1-3/16" | 1-5/16" | BU9 | RBU9 | 21 | BBU9 | 18 |
3/4" | 1-5/16" | 1-1/2" | B9 | RB9 | 21 | BB9 | 18 |
3/4" | 1-1/2" | 1-11/16" | B10 | - | 21 | - | - |
Hose ID | Hose OD | Plated Malleable Iron | Stainless Steel | Brass | |||
---|---|---|---|---|---|---|---|
Size | From: | To: | Part # | Part # | Torque** | Part # | Torque** |
1/2" | 29/32" | 1-1/32" | 968 | - | 6 | - | - |
1" | 1-13/32" | 1-9/16" | 156* | - | 21 | - | - |
1" | 1-17/32" | 1-23/32" | BU14 | RBU14 | 21 | BBU14 | 18 |
1" | 1-11/16" | 1-15/16" | B14 | RB14 | 21 | BB14 | 18 |
1" | 1-15/16" | 2-1/8" | B15 | - | 21 | - | - |
1-1/4" | 1-1/2" | 1-25/32" | BU18 | - | 40 | - | - |
1-1/4" | 1-11/16" | 1-7/8" | 187* | - | 21 | - | - |
1-1/4" | 1-25/32" | 2-3/32" | BU19 | - | 40 | - | - |
1-1/4" | 1-7/8" | 2-1/16" | 206* | - | 21 | - | - |
1-1/4" | 2-1/8" | 2-3/8" | B19 | RB19 | 40 | BB19 | 28 |
1-1/2" | 1-13/16" | 2" | BU22 | - | 40 | - | - |
1-1/2" | 2" | 2-7/32" | B22 | - | 40 | - | - |
1-1/2" | 2" | 2-1/8" | 212* | - | 21 | - | - |
1-1/2" | 2-1/16" | 2-1/4" | 225* | - | 40 | - | - |
1-1/2" | 2-3/16" | 2-3/8" | BU24 | RBU24 | 40 | BBU24 | 28 |
1-1/2" | 2-3/8" | 2-9/16" | B24 | RB24 | 40 | BB24 | 28 |
1-1/2" | 2-9/16" | 2-3/4" | B25 | - | 40 | - | - |
2" | 2-1/4" | 2-1/2" | 250* | - | 40 | - | - |
2" | 2-11/32" | 2-17/32" | BU28 | - | 60 | - | - |
2" | 2-1/2" | 2-3/4" | 275* | - | 40 | - | - |
2" | 2-1/2" | 2-25/32" | BU29 | RBU29 | 60 | BBU29 | 40 |
2" | 2-3/4" | 3-1/16" | B29 | RB29 | 60 | BB29 | 40 |
2" | 2-3/4" | 3-1/16" | 306* | - | 60 | - | - |
2" | 3-3/32" | 3-7/16" | B30 | - | 60 | - | - |
2-1/2" | 3-1/16" | 3-1/2" | 350* | - | 60 | - | - |
2-1/2" | 3-3/32" | 3-7/16" | BU34 | - | 60 | - | - |
2-1/2" | 3-1/2" | 3-15/16" | B34 | - | 150 | - | - |
3" | 3-1/2" | 3-3/4" | 375* | - | 60 | - | - |
3" | 3-1/2" | 3-15/16" | BU35 | - | 150 | - | - |
3" | 3-3/4" | 4" | 401* | - | 150 | - | - |
3" | 3-13/16" | 4-1/16" | B35 | - | 150 | - | - |
3" | 4" | 4-3/16" | 418* | - | 200 | - | - |
3" | 4-1/16" | 4-7/16" | B39 | - | 200 | - | - |
3" | 4-3/16" | 4-1/2" | 450* | - | 200 | - | - |
Hose ID | Hose OD | Plated Malleable Iron | ||
---|---|---|---|---|
Size | From: | To: | Part # | Torque** |
3" | 4-1/4" | 4-13/16" | BS39 | 150 |
4" | 4-5/8" | 5" | B45 | 150 |
4" | 4-7/8" | 5-1/4" | BS49 | 200 |
4" | 5-1/4" | 5-19/32" | BU49 | 200 |
4" | 5-17/32" | 5-15/16" | B49 | 200 |
6" | 6-7/8" | 7-3/8" | 750 | 200 |
6" | 7-1/2" | 8" | 850 | 200 |