ApplicationsOne of our most popular synthetic rubber sheets, Neoprene is also one of the least expensive of our sheet rubber selection. Neoprene sheet is specially compounded to provide good resistance to oils and gasoline in such applications as gaskets and flanges in gas permeable situations. Also applicable for bumpers, pads and sealing usages. |
Style #10A commercial blend, Neoprene compound, adaptable to extreme weather conditions since it resists rotting, checking and cracking due to ozone exposure. Has good low temperature flexibility and is oil resistant. Meets ASTM specifications for 1BC Material. |
Style #15 (50% Base)A premium grade product that has very good oil resistant characteristics. The 50% Neoprene Base Formula resists ozone and is highly recommended for hot and cold applications. |
Style #12 (Matte Finish)Style 12 is a commercial blended neoprene sheet with a matte finish on one side. It is free of talc and release solutions which make it excellent for applications that involve the use of pressure sensitive adhesives. (This style is not shown in the table; the specs are the same as Style 10, available in 50 through 80 durometer only. |
Style | Thickness | Width | Duro. | Tensile | Elong. | Temp. | Wt./Sq. Ft. 1/8" | Specifications |
---|---|---|---|---|---|---|---|---|
10 | 1/16 thru 1 | 36 & 48 | 40 | 800 | 350 | -20 to +170ºF | .83 | ASTM D2000 SAE J200, 1BC408 MIL R-3065, SC 408 |
10 | 1/16 thru 2 | 36 & 48 | 50 | 800 | 300 | -20 to +170ºF | .87 | ASTM D2000 SAE J200, 1BC508 MIL R-3065, SC 508 |
10 | 1/32 thru 2 1/16,1/8,1/4 | 36&48 72 | 60 | 900 | 300 | -20 to +170ºF | .90 | ASTM D2000 SAE J200, 1BC609 MIL R-3065, SC 609 |
10 | 1/16 thru 2 | 36 & 48 | 70 | 1000 | 200 | -20 to +170ºF | .90 | ASTM D2000 SAE J200, 1BC710 MIL R-3065, SC710 |
10 | 1/16 thru 2 | 36 & 48 | 80 | 1000 | 100 | -20 to +170ºF | .97 | ASTM D2000 SAE J200, 1BC810 MIL R-3065, SC 810 |
15 | 1/16 thru 1 | 36 & 48 | 50 | 1000 | 300 | -40 to +180ºF | .87 | ASTM D2000 1BC510 MIL-R-3065, SC 510 |
15 | 1/16 thru 1 | 36 & 48 | 60 | 1000 | 300 | -40 to +180ºF | .90 | ASTM D2000 1BC 610 MIL-R-3065, SC 610 |
15 | 1/16 thru 1 | 36 & 48 | 70 | 1000 | 200 | -40 to +180ºF | .90 | ASTM D2000 1BC 710 MIL-R-3065, SC 710 |
Oil Resistant Nitrile Sheet-BlackNitriles are special purpose rubbers with superior oil and solvent resistant properties compared to most other polymers. |
Style #35Commercial blend nitrile is offered in a range of five durometers: 40 through 80 duro. in order to perform in a wide variety of applications. |
Style | Thickness | Width | Duro. | Tensile | Elong. | Temp. | Wt./Sq. Ft. 1/8" | Specifications |
---|---|---|---|---|---|---|---|---|
35 | 1/16 thru 1 | 36 & 48 | 40 | 800 | 350 | -20 to +170ºF | .83 | ASTM D2000 SAE J200, 1BE408 |
35 | 1/32 thru 1 | 36 & 48 | 50 | 800 | 300 | -20 to +170ºF | .87 | ASTM D2000 SAE J200, 1BE 508 |
35 | 1/32 thru 1 | 36 & 48 | 60 | 900 | 300 | -20 to +170ºF | .87 | ASTM D2000 SAE J200, 1BE 609 |
35 | 1/32 thru 2 | 36 & 48 | 70 | 1000 | 200 | -20 to +170ºF | .90 | ASTM D2000 SAE J200, 1BE 710 |
35 | 1/16 thru 1/4 | 36 & 48 | 80 | 1000 | 100 | -20 to +170ºF | .87 | ASTM D2000 SAE J200, 1BE 810 |
ApplicationsExcellent for all types of washers, gaskets and seals which require resistance to conditions of oils and aromatic fuels. Typical applications include carburetor gaskets, fuel pumps, diaphragms and aircraft hose gaskets. |
Style #36Premium nitrile is formulated to give maximum oil resistance. The higher cost is offset by longer service life in demanding applications. This is a factory stock item in 60 durometer. Other hardnesses are available on a made-to-order basis |
Style | Thickness | Width | Duro. | Tensile | Elong. | Temp. | Wt./Sq. Ft. 1/8" | Specifications |
---|---|---|---|---|---|---|---|---|
36 | 1/16 thru 1/4 | 36 | 60 | 1300 | 300 | -40 to +180ºF | .80 | ASTM D2000 6BG 613, A14, B14, EO14, EO34, F17 |
Style 37 - White FDA | |
---|---|
A sheet specially formulated for its whiteness, used in food, pharmaceutical, and cosmetic processing. Made from FDA-approved | ingredients, it is non-toxic, non-marking and non-allergenic. It has good abrasion resistance and handles oily and greasy products well. |
Style | Thickness | Width | Duro. | Tensile | Elong. | Temp. | Wt./Sq. Ft. 1/8" | Specifications |
---|---|---|---|---|---|---|---|---|
37 | 1/16 thru 1/4 | 36 & 48 | 60 | 1000 | 350 | -25 to +180ºF | .93 | FDA Approved Non-Marking |
Style 20 - Red | |
---|---|
An economical red sheet for use in low pressure applications with no oil resistance requirements. Well suited for the heating and plumbing trades. Has good aging, | abrasion and tear resistant properties. Refer to physical properties and ASTM data in assessing suitability for intended applications. Also available in black on a special order basis. |
Style | Thickness | Width | Duro. | Tensile | Elong. | Temp. | Wt./Sq. Ft. 1/8" | Specifications |
---|---|---|---|---|---|---|---|---|
20 | 1/32 thru 1/4 | 36, 48 & 72 | 75 | 400 | 150 | -20 to +170ºF | 1.17 | ASTM D1330 Grade II ASTM D2000 Type AA |
Style | Thickness | Width | Duro. | Tensile | Elong. | Temp. | Wt./Sq. Ft. 1/8" | Specifications |
---|---|---|---|---|---|---|---|---|
21 | 1/16 thru 1/4 | 36 | 75 | 700 | 150 | -20 to +170ºF | .90 | ASTM D1330 Grade I |
Style | Thickness | Width | Duro. | Tensile | Elong. | Temp. | Wt./Sq. Ft. 1/8" | Specifications |
---|---|---|---|---|---|---|---|---|
27 | 1/16 thru 1 | 36 & 48 | 40 | 3000 | 600 | -20 to +140ºF | .63 | ASTM D2000 SAE J200, 1AA 430 |
Tan floating stock has superior resilience, tensile, elongation and abrasion resistance properties. It has good tear strength and is resistant to water, most salts, mild acids and many other chemicals. | Not suited for environments involving ozone, strong acids, animal fats, oils, greases and most hydrocarbons. Non-marking and non-toxic. Also available in black. |
Style | Thickness | Width | Duro. | Tensile | Elong. | Temp. | Wt./Sq. Ft. 1/8" | Specifications |
---|---|---|---|---|---|---|---|---|
28 | 1/16 thru 1 | 36 & 48 | 40 | 3000 | 600 | -20 to +140ºF | .63 | ASTM D2000 SAE J200, 1AA 430 |
Thermoplastic, economical sheet for many non-critical applications. Good water, ozone, | and chemical resistance and good weathering characteristics. Limited temperature tolerance. |
Style | Thickness | Width | Duro. | Tensile | Elong. | Temp. | Wt./Sq. Ft. 1/8" | Specifications |
---|---|---|---|---|---|---|---|---|
30 | 1/16 thru 1/4 | 36 | 70 | 1000 | 250 | -20 to +160ºF | .83 | Smooth Finish |
A superior rubber for outdoor and high temperature applications. Good electrical properties. | Resists animal and vegetable oils, ozone, steam, water, and oxygenated solvents. |
Commercial EPDM is the most economical EPDM sheet offered. Intended to be used | in less critical applications where temperatures are of an intermittent nature. |
Style | Thickness | Width | Duro. | Tensile | Elong | Temp. | Wt./Sq. Ft. 1/8" | Specifications |
---|---|---|---|---|---|---|---|---|
40 | 1/16 thru 1/4 | 36 & 48 | 50 | 800 | 300 | -40 to +212ºF | .73 | ASTM D2000 SAE J200, 3BA (508 608 708), C12 MIL R-3065 RS 508 608 708, C12 |
60 | 300 | |||||||
70 | 250 |
Style | Thickness | Width | Duro. | Tensile | Elong | Temp. | Wt./Sq. Ft. 1/8" | Specifications |
---|---|---|---|---|---|---|---|---|
45 | 1/16 thru 1/4 | 36 & 48 | 50 | 1500 | 300 | -40 to +225ºF | .73 | ASTM D2000 SAE J200, 3BA (515 615 715 815), B13 C12 F17 MIL R-3065 RS 515 615 715 815, C12 |
60 | 300 | |||||||
70 | 250 | |||||||
80 | 150 |
Style | Thickness | Width | Duro. | Tensile | Elong | Temp. | Wt./Sq. Ft. 1/8" | Specifications |
---|---|---|---|---|---|---|---|---|
475 | 1/16 thru 1/4 | 36 | 50, 60 | 2000 | 400 | -55 to +300ºF | .73 | ASTM D2000 SAE J200, 5BA 520 620 C12 F17 F19 |
Good electrical, weathering, and vibration damping properties. Withstands elevated temperatures well, resists gas permeation, acids, alkalis and ozone. Not resistant to petroleum | based oils, solvents and aromatic hydrocarbons but will withstand animal and vegetable oils. A superior product with unique characteristics for many challenging applications. |
Style | Thickness | Width | Duro. | Tensile | Elong. | Temp. | Wt./Sq. Ft. 1/8" | Specifications |
---|---|---|---|---|---|---|---|---|
60 | 1/16 thru 1/4 | 36 | 60 | 1200 | 350 | -40 to +225ºF | .83 | ASTM D2000 Type BA |