The Extension Gasket Cutter saves money and costly downtime by enabling anyone to cut accurate gaslets, quickly and efficiently on the job, when they are needed! Cuts all gasketing materials, including compressed asbestos, cork, rubber, Teflon®, fibre, etc. Cutting capacity from ¼" to 60" in diameter, and up to ¾" thick. An efficient and easy-to-use tool that eliminates waste and costly errors. Available in six convenient kits to meet a broad range of cutting requirements.
All Styles packed in metal box. See parts list for parts contained in each Style. Style No. 6 is less Fig. 12 Cutting Board.
Fig. 1 - Cutter Block and Head | Fig. 9 - Center Pin Ferrule | ||
Fig. 2 - Cutter Head Screws | Fig. 10 - Extension Bar (12" to 24") | ||
Fig. 3 - Cutting Blades (6 per pkg.) | Fig. 11 - Extension Bar (over 24") | ||
Fig. 4 - Pivot Post | Fig. 12 - Cutting Board Complete | ||
Fig. 5 - Pivot Post for Extension Bars | Fig. 14 - Cutting Pad | ||
Fig. 6 - Thumb Nut | Fig. 15 - Cutting Knob | ||
Fig. 6A - Thumb Nut for Fig. 11 | Fig 16 - Post with Offset Pin | ||
Fig. 7 - Fibre Washer | Fig. 17 - Piercing Tool | ||
Fig. 8 - Short Center Pin | Fig. 18 - Screw Driver | ||
Fig. 8A Long Center Pin |
Additional Parts Available |
---|
Fig. 3A - Heavy Duty Cutting Blades (6 per pkg.) |
Fig. 12A - Cutting Board Complete, size 24" x 24" |
Fig. 12B - Cutting Board Complete, size 30" x 30" |
Fig. 14A - Cutting Pad, size 24" x 24" |
Fig. 14B - Cutting Pad, size 30" x 30" |
Arch punches are drop forged in one piece from the finest special carbon steel in sizes from 3/16" to 2¼" diameter. Larger sizes are made with our properly engineered two piece welded construction. A unique feature of the arch punch is the inside taper which permits the punchings to clear easily through the barrel. Punches have fully polished barrel and black enamel handle.
The cutting edge is fully tempered all the way through and properly finished to provide long use and trouble free punching. There is no other hollow punch that can compare.
Meets government standards.
Size | UPC # | Size | UPC # | Size | UPC # |
---|---|---|---|---|---|
3/16" | 01010 | 1-1/4" | 01044 | 2-5/8" | 01088 |
1/4" | 01012 | 1-5/16" | 01046 | 2-3/4" | 01092 |
5/16" | 01014 | 1-3/8" | 01048 | 2-13/16" | 01093 |
3/8" | 01016 | 1-7/16" | 01050 | 2-7/8" | 01096 |
7/16" | 01018 | 1-1/2" | 01052 | 3" | 01100 |
1/2" | 01020 | 1-5/8" | 01056 | 3-1/16" | 01102 |
9/16" | 01022 | 1-3/4" | 01060 | 3-1/8" | 01104 |
5/8" | 01024 | 1-13/16" | 01062 | 3-3/16" | 01106 |
11/16" | 01026 | 1-7/8" | 01064 | 3-1/4" | 01108 |
3/4" | 01028 | 2" | 01068 | 3-3/8" | 01112 |
13/16" | 01030 | 2-1/16" | 01070 | 3-7/16" | 01114 |
7/8" | 01032 | 2-1/8" | 01072 | 3-1/2" | 01116 |
15/16" | 01034 | 2-3/16" | 01074 | 3-5/8" | 01120 |
1" | 01036 | 2-1/4" | 01076 | 3-3/4" | 01124 |
1-1/16" | 01038 | 2-3/8" | 01080 | 3-13/16" | 01126 |
1-1/8" | 01040 | 2-7/16" | 01082 | 3-7/8" | 01128 |
1-3/16" | 01042 | 2-1/2" | 01084 | 4" | 01132 |
These punches should be used on a wood or plastic cutting block. The use of a wooden or rawhide mallet is recommended. Steel hammers are not recommended.
This set of seven arch punches includes the sizes most widely used. They are put up in a sturdy, easy to use canvas tool roll.
One each of the following sizes #149 Arch Punch | |||||||
---|---|---|---|---|---|---|---|
Sizes | 1/4" | 3/8" | 1/2" | 5/8" | 3/4" | 7/8" | 1" |
UPC # | 01180 |
This set of seven arch punches includes the sizes incremented by 2/16". They are put up in a sturdy, easy to use canvas tool roll.
One each of the following sizes #149 Arch Punch | |||||||
---|---|---|---|---|---|---|---|
Sizes | 3/16" | 5/16" | 7/16" | 9/16" | 11/16" | 13/16" | 15/16" |
UPC # | 01181 |